Stone Weight Calculator: Granite & Marble Slabs

Solid stone · Slabs · Blocks

Stone Weight Calculator

Estimate how much an individual stone piece or a batch weighs. Choose a shape, enter dimensions and material density, and see pounds, kilograms, US short tons and metric tonnes.

1. Select stone and shape

Identical pieces. One by default.
2. Enter dimensions
Measure solid stone dimensions, not the area it will cover after installation.
3. Adjust density and any cutouts
Subtracts a volume percentage. Leave 0 for solid pieces.
Illustrative solid granite density. Replace it with the product test report where available. Do not use loose aggregate bulk density here.

How to calculate the weight of natural stone

To estimate the weight of a granite, marble, limestone or other solid stone piece, find its volume in cubic meters and multiply by its density in kilograms per cubic meter. The result is the approximate mass in kilograms. Convert kilograms to pounds or tons if you need to plan material handling or transportation.

Stone mass (kg) = net solid volume (m³) × density (kg/m³). For a batch, multiply the weight of one piece by the number of identical pieces. If a slab has a known percentage of voids or cutouts, subtract that percentage of volume before estimating its mass.

Supported stone shapes and formulas

  • Rectangular slab / block: length × width × thickness.
  • Cylinder: π × (diameter ÷ 2)² × height.
  • Sphere: (4 ÷ 3) × π × (diameter ÷ 2)³.
  • Irregular stone: enter its known solid volume from a supplier drawing or suitable measurement method.

Slab weight per square foot: 2 cm, 3 cm and 1¼-inch stone

Need a fast slab-weight estimate before entering measurements? The examples below use an illustrative solid-stone density of 2,700 kg/m³ (about 168.6 lb/ft³). They are calculated weights, not guaranteed figures for granite or marble from a particular quarry.

Slab thicknessApprox. lb per ft²Approx. kg per ft²6 × 3 ft slab (18 ft²)
2 cm11.1 lb5.0 kg199 lb
3 cm16.6 lb7.5 kg299 lb
1¼ inch (31.75 mm)17.6 lb8.0 kg316 lb

Formula: stone slab weight = length × width × thickness × solid-stone density, with consistent units. For pounds per square foot, multiply the slab thickness in feet by the density in pounds per cubic foot. A marble slab can have a different density from a granite slab, even at the same thickness. Enter your supplier’s value and actual dimensions above for a better estimate; cutouts and edge profiles may affect the final weight.

Conversions follow NIST’s SI conversion guidance. These figures are for estimation only and do not determine safe lifting capacity. For loose gravel rather than a solid slab, use the Stone Calculator with its separate bulk-density assumptions.

Example: granite slab weight

For one solid granite slab measuring 6 feet long, 3 feet wide and 2 inches thick, the gross volume is approximately 0.08495 cubic meters. Using an illustrative density of 2,700 kg/m³, its estimated weight is about 229 kg, or 506 lb. This estimate assumes a uniform, solid slab with no cutouts. Use the Try an Example button to load these dimensions.

Illustrative stone density presets

Stone density depends on its composition, porosity and the particular quarry or product. These presets are rough starting assumptions, not guaranteed values. Change the density to match your supplier’s measured result.

Solid stoneStarting density (kg/m³)
Granite2,700
Marble2,700
Limestone2,400
Sandstone2,300
Slate2,750
Quartzite2,650
Basalt2,950
Travertine2,400
Soapstone2,750

Measurement conversions

QuantityConversion
1 foot0.3048 meters (exact)
1 pound0.45359237 kg (exact)
1 US short ton2,000 pounds (exact)
1 metric tonne1,000 kilograms (exact)

Frequently asked questions

How do I estimate a granite countertop slab’s weight?

Enter its total length, width and thickness, choose solid granite and use the supplier’s specific density if known. Enter the cutout percentage only if you have a reasonable volume estimate for the removed material. For lifting and installation, use verified fabricator specifications rather than this calculator alone.

Does this calculator work for gravel?

No, this page is optimized for solid stone pieces. Gravel and crushed stone have empty spaces between particles and need a separate loose bulk density. Use the general Stone Calculator for loose aggregate quantity estimates.

Does the calculator include mortar, reinforcement or a pallet?

No. Results represent the stone itself, with optional cutout adjustment. Supporting materials, packaging and lifting equipment are excluded.

How do I calculate an irregular stone’s weight?

If you have a reliable volume measurement, select Known volume, choose the unit and enter that volume. Multiply by the stone density to estimate the weight. For complex shapes, ask a qualified professional for a verified volume or weight.

Are US short tons and metric tonnes the same?

No. One US short ton is exactly 2,000 pounds (about 907.185 kg). One metric tonne is exactly 1,000 kg. The calculator shows both explicitly.

Important: This is an educational mass estimate, not an approved lifting plan, structural-load check, transport permit or engineering certificate. Verify material density, cutouts, handling loads and safety requirements with your supplier or qualified professional. See our calculation methodology and disclaimer. Density determination for dimension stone is addressed by ASTM C97/C97M (some stone categories have separate methods).